This paper presents a new topology for a microwave active mixer using compact microstrip diplexer constituted from two dual-mode open loop resonators. The resonators are tuned to the radio frequency (RF) and local-oscillator (LO) frequencies, respectively, to effectively isolate the two input signals, while the diplexer output port is connected to the gate circuit of a commercial low cost GaAs pHEMT transistor. The drain circuit of the active device is connected to the load via an intermediate-frequency (IF)-modified Chebyshev low-pass filter to remove the unwanted RF and LO signals and reduce other spurious frequencies at the output of the mixer circuit. The circuit has been designed and constructed for an RF of 850 MHz, LO frequency of 1050 MHz, and an IF of 200 MHz. Experimental measurements show that the circuit provides a conversion gain of 18 dB at LO drive power of +2 dBm. It also operates satisfactorily over the RF range from 800 to 900 MHz with good image frequency rejection and stable operation.

A two-port ceramic-based antenna loaded with partially reflecting surface (PRS) is structured and explored. Fan-shaped slot is utilized to create circularly polarized wave in both frequency ranges. Dual frequency ranges are due to hybrid mode creation inside the ceramic material, i.e. HEM11δ and HEM12δ modes. PRS is used to change the phase gradient, which in turn tilts the radiation beam (±35°) obtained from different port in opposite direction. This concept is useful to reduce the envelop correlation coefficient using far-field. Experimental verification confirms that the designed antenna works from 26.1 to 27.5 GHz and 31.7 to 33.6 GHz along with less than 3-dB axial ratio from 26.5 to 27.1 GHz and 31.9 to 33.1 GHz respectively. Orthogonal placement of ports introduces the concept of polarization diversity and decreases the coupling between ports by an amount of −25 dB. Good gain value (up to 7.0 dBi) and better value of diversity performance make the designed radiator applicable for 5 G millimeter-wave uses.

A novel reconfigurable circular microstrip G-slotted antenna having a circularly defected ground structure (DGS) capable of switching its resonance frequency for several microwave applications is presented in this paper. Reconfigurability of the proposed G-slot antenna is obtained by incorporating three PIN diodes. One diode is embedded in the patch and two diodes are integrated into the DGS structure at appropriate places in the slot to achieve four different wireless applications such as aeronautical radio navigation (4.3 GHz with gain 3.6 dB), satellite communication (3.78 GHz with gain 3.7 dB), mobile communication (4.55 GHz with gain 4.0 dB), and WiMAX (3.35 GHz with gain 3.3 dB). These four bands are achieved depending on the different biasing conditions of the three PIN switches used. Antenna performance has been analyzed in ANSYS Electronics Desktop 2018.2 software. The equivalent circuit component of the switching element (PIN diode) has been considered and designed during the simulation. The creative structure lies in the way that it exhibits higher gain with compact size than the previously reported similar antenna. A prototype of the proposed patch antenna has been fabricated on a Roger substrate and its testing and measurement have been performed to demonstrate its desirable characteristics and features.

A novel microstrip filtering antenna with slot coupling feed is presented in this work. An asymmetric interdigital coupling structure is used for the feed to excite the patch antenna through gap-fed coupling. Introducing a U-shaped slot on the patch surface modifies the current path to attain different resonant modes. The asymmetric coupled fingers in the low-frequency band generate a radiation null of −64 dBi, while additional resonances introduced in the high band broaden the bandwidth from 4.9 to 5.3 GHz. A horizontally shorted microstrip branch produces another null point of −28 dBi between the bands, enabling steeper roll-off and further improvement in frequency selectivity. The proposed filtering antenna provides a flexible filter response without requiring extra filtering circuits, with appreciable peak gains (6.1 dBi and 7.1 dBi) and stable radiation characteristics. This makes it suitable for WLAN (Wireless Local Area Network) and ISM (Industrial Scientific Medical) systems applications.

The present work studies the design of a high impedance surface (HIS)-based bowtie antenna in the framework of characteristic mode analysis (CMA) and proposes the method of higher order mode suppression. A triangular-elliptical bowtie antenna operating in the frequency range of 1.6–6 GHz is designed. The radiating and higher order modes of the proposed antenna are identified using CMA, and an HIS structure is used to enhance the desired mode and to suppress the higher order mode in order to get high gain, good front-to-back ratio (FBR), and stable radiation characteristics. The final designed HIS-based bowtie antenna gives stable radiation patterns from 1.7 to 5.5 GHz with a maximum boresight gain of 10.5 dB. Also, gain from 6.5 to 12 dB and FBR from 8 to 18 dB are obtained in the operating bandwidth. The proposed antenna features the advantages of low profile, wideband and high boresight gain making it suitable for ground-penetrating radar applications.

This paper investigates the electromagnetic scattering characteristics in arid zone and proposes methods for monitoring and improving ecological agriculture, vegetation landscape and desertification in arid zone, based on the modified small slope approximation (SSA) electromagnetic scattering model. The dielectric properties of dryland soils are studied in the paper, and the variation curves of soil dielectric constant with humidity and electromagnetic frequency are plotted. In order to reproduce the geomorphological features of the dryland areas, a two-dimensional geometric model of the ground environment is established using Monte Carlo methods combined with Gaussian spectral functions. An algorithm model based on the modified SSA is developed, and the algorithm was validated and analyzed to verify its reliability. In the simulations, the southeastern region of Ejina Banner, Inner Mongolia was taken as a typical arid region, and the simulation parameters are obtained from the actual measurement data of the region. The study finds that the electromagnetic scattering characteristics of the arid zone are influenced by soil water content, ground roughness and incident wave electromagnetic frequency, and there is regularity. The results of this paper can be effectively combined with remote sensing technology to contribute to many researches on soil moisture inversion and ecological condition of vegetation, which are important in many aspects such as irrigation control, ecological research, vorticity covariance, and climatology of slope stability.

A wideband tunable balanced phase shifter is achieved by utilizing varactor-loaded coupled lines (VLCLs)-embedded multistage branch-line structure. The tunable phase shift with low in-band phase deviation is attributed to the regulation in phase shift of the VLCLs and the horizontal microstrip lines in series. The wideband differential-mode (DM) impedance matching and common-mode (CM) suppression are due to multiple DM transmission poles and CM transmission zeros, which are brought about by the cascade of VLCLs and a microstrip line with short-circuited stubs in the DM-equivalent circuit and open-circuited stubs in the CM-equivalent circuit, respectively. Compared with the state-of-the-art tunable balanced phase shifters, the proposed design not only has the advantages of wide operating bandwidth (BW) with low in-band phase deviation but also has low insertion loss and easily fabricated structure. Theoretical analysis and design procedure were conducted, resulting in a prototype covering the frequency of 1.8 GHz. This prototype offers a tunable phase shift capability ranging from 0° to 90°. The prototype exhibits an operating BW of 45%, with a maximum phase deviation of ±6°. It also achieves a 10 dB DM return loss and CM suppression, while maintaining a maximum insertion loss of 2.5 dB.

A fourth-order bandpass filter with dual-wide passbands is proposed in this article. The novelty of the proposed work is the realization of a dual-band bandpass filter with closely spaced passbands, wide passband bandwidth, high rejection between the passbands, using a novel combination of open stub tapped series coupled lines (CLs) and shunt transmission line loaded with end connected CLs. The characteristics of the proposed dual-wideband bandpass filter are investigated by adopting even–odd mode analysis. The transmission zeros generated by the transmission line loaded with an end-connected CL and open stub are utilized to achieve a high skirt rate. A rejection better than 55 dB is achieved with a single transmission zero between the two passbands indicating high isolation and close passbands. The dual-wideband filter is designed and manufactured to operate at 1.33 and 2.32 GHz. The experimented 3-dB fractional bandwidths of the two pass frequency bands are 40.6% and 24.13%. The proposed filter’s tested frequency responses agree well with simulated results. The proposed device can be used in various applications such as telecommunications, satellite communications, radar systems, imaging, and spectroscopy.

Large reflector antennas, such as the European Space Agency deep space antennas (DSAs), practically always require struts to support the sub-reflector. While inevitable, they deteriorate the antenna performance. To minimize this deterioration, it is pivotal to understand the role played by different features, including struts diameter and shape. This paper proposes a detailed numerical investigation on the impact of these features on antenna efficiency and side lobes, for a test case comprising both DSA3 and DSA4. It is demonstrated, for the first time in a comprehensive and quantitative way that includes different permutations for the strut design, that both features are significant to define the deterioration, thus providing a significant feedback for struts design.

The increasing demand for wireless communication has emphasized the need for multiband antennas. This study presents a novel design for a multiband antenna with reduced specific absorption rate (SAR), high gain, and improved front-to-back ratio (FBR) achieved through the integration with a 4 × 4 artificial magnetic conductor (AMC) surface. The proposed antenna covers a wide range of wireless frequency bands, including Industrial, Scientific, and Medical, Wireless Local Area Network, Worldwide Interoperability for Microwave Access, Wi-Fi 6E, and 7, with resonating frequencies at 2.4, 3.2, 5.5, 7.5, and 10 GHz. The AMC unit cell creates four zero-degree reflection phases with double negative properties at 2.5, 3.8, 5.5, and 7.5 GHz. The compact design measures 0.23λ0 × 0.296λ0 × 0.0128λ0 and placed 0.104λ0 above an AMC surface of size 0.512λ0 × 0.512λ0 × 0.1296λ0. This structure enhances the gain by up to 8.55dBi at 6.01 GHz. The proposed antenna has −10 dB impedance bandwidth for these corresponding frequencies viz 2.34–2.43 GHz (3.77%), 2.81–3.83 GHz (30.72%), 4.82–6.21 GHz (25.20%), 7–7.65 GHz (8.87%), and 8.06–10.31 GHz (24.5%). An overall average percentage reduction value of SAR taken at these frequencies has been found to be 96.11% with AMC structure. The antenna sample was successfully fabricated, and the experimental results have been found to match well with the simulation results. This integrated design offers a promising solution for wearable off-body communication devices.

In this paper, the design of a circularly polarized (CP) multiple-input–multiple-output (MIMO) antenna system is presented, utilizing a dielectric resonator (DR). This presented antenna system is subsequently integrated with a multifunctional filter, all meticulously structured on a single substrate. The multifunctional filter operates in three modes: reconfigurable band-pass and band-reject filter as well as all-pass filter. The overall structure works as a tunable filtenna. The designed filtenna is expanded into a two-port MIMO system on a unified substrate, providing strong port isolation below −28.5 dB. The overall dimension of proposed radiator is 180 × 180 × 1.6 mm3. The value of peak gain is 5.19 dBic. By switching the states of PIN diodes, the designed filtenna operates as a sensing and communicating antenna for interweave and underlay cognitive radios (CRs). The proposed antenna supports the CP waves within the working band, i.e., 3.6–4.5 GHz. The simulated results are validated by comparing them with the measured results showing less variation among them. MIMO parameters, including the envelope correlation coefficient and diversity gain, have been calculated for the proposed filtenna, representing its suitability for 5G-CR applications.

A dual-band angular-stable transmissive linear to circular polarization converter based on metasurface is proposed and demonstrated in this work. The converter consists of three layers. The top and bottom layers are formed by an array of double split-ring layers. The unit cell of the central layer contains a square loop nesting a slant dipole. The split-rings create two resonances, enabling dual-band operation. The slant dipole and square loop are useful for improving the quality of circular polarization conversion. It is shown that the proposed polarization converter converts the incident linearly polarized wave into circularly polarized wave with opposite polarization modes over the frequency ranges of 8.77–10.58 and 17.59–19.88 GHz. The angular stability is up to 60° for 3 dB axial ratio. Moreover, the thickness of unit cell has a wavelength below 0.06 at the lower band. Compared with other designs in the literature, the structure bears merits of wideband response, high angular stability, and low-profile property within dual-band operational region. To validate the design, a sample prototype was designed, fabricated, and measured. The measured results are in good agreement with the simulated ones.

A design of a microwave absorber based on frequency selective surface resonating in X-band having ultrathin thickness, polarization controlled behavior, and increased absorption bandwidth has been reported. The reported absorber having its unit cell embodied of multiple resonating structures which includes conventional square, circular, and butterfly shaped resonators resulting in three absorption apexes at 9.44, 10.00, and 10.53 GHz (all in X band) with 99.9%, 99%, and 95.1% of absorptivity obtained at the frequencies of resonances. It demonstrates a wide full width at half maximum having 1.48 GHz as bandwidth, at the expense of using an ultrathin substrate of 0.0096 λ0, where λ0 is the wavelength with respect to lowest resonating frequency, i.e. 9.44 GHz. The unit cell is fourfold symmetric exhibiting independence about the absorber’s polarity, as well as, it behaves stable over the outspread angle up to 45 degrees for both transverse magnetic and transverse electric polarized wave under sloped incident angle. The absorption behavior has been demonstrated by plotting the distribution of surface-currents and electric fields at the frequencies of resonance. The fabricated prototype of the presented design is tested at X-band and the obtained results concur with the simulated results.

This work presents a study where a sinusoidal corrugated antipodal Vivaldi antenna (SC-AVA) operating in the ultra-wideband (UWB) region is employed as a transducer for microwave imaging (MWI) of a cancerous breast. The functionality of the antenna within the UWB range is confirmed based on performance parameters like return loss, gain, radiation pattern, fidelity factor, and group delay. E-field distribution, H-field distribution, and near field directivity simulations in the presence of the breast phantom have also been carried out and reported. The practical application of the developed antenna for biomedical imaging is evaluated by measuring the specific absorption rate (SAR) readings at multiple frequencies within its operating range. The SAR readings are obtained from an electromagnetic simulator by modelling a realistic heterogeneous breast phantom with multiple embedded tumors, and placing them in close proximity to the transducer. The modelled SC-AVA is further utilized for imaging multiple tumors hidden inside the gland layer of the heterogeneous breast phantom developed in-house. The fabricated breast phantom is scanned using the in-house developed multistatic MWI setup. Based on the data obtained from the scanning setup the images are reconstructed using both the delay multiply and sum (DMAS) and iterative DMAS imaging algorithms. Furthermore, a comparison of the reconstructed images is done to check in which case the obtained images are closer to the fabricated breast phantom.

This paper proposes a passive filtering antenna for ultra-wideband (UWB) applications. The edge chamfering technique is adopted to construct the UWB antenna. The designed UWB antenna has a fractional bandwidth of 135%. A low-pass filter (LPF) is embedded on the feed line of the UWB antenna to convert it into a narrowband antenna that works at 2.45 GHz with 29.5% fractional bandwidth by removing the high-frequency components. The LPF is a transmission line with a stepped impedance configuration loaded with an H-shaped unit cell. The proposed filtering antenna is fabricated and tested. The measured results indicate the gain is >4.2 dBi and the radiation efficiency is >75%.

This article focuses on reducing mutual coupling between the ports of dielectric resonator antenna (DRA) using defected ground structures (DGSs). The antenna has the dimension of 50 mm × 50 mm × 8.5 mm. The resonating element in the proposed two-port radiator consists of a cylindrical structure of alumina ceramic (ɛr = 9.8). The rectangular-shaped aperture is utilized to excite both of the resonating elements. The resonating ceramic elements acting as radiators are offset-fed to enhance the antenna’s coupling. Combining interdigital-shaped and semicircular arc-shaped DGSs improves isolation between two resonating elements, embodying the structural novelty. The measured operating frequency range of Port-1 and Port-2 is 5.19–6.7 and 5.15–6.68 GHz, resonating at 5.58 and 5.56 GHz, respectively. The measured mutual coupling between the two ports is −35.5 dB. The measured gain for Port-1 is depicted to be 5.5 dB. The presented multiple-input–multiple-output (MIMO) radiator in this article is an appropriate candidate for WLAN (5.25–5.35, 5.47–5.725, 5.725–5.85, 5.850–5.925 GHz) and WiMAX(5.5 GHz) applications. All the simulated and experimentally observed MIMO parameters of the radiator are discovered to be within optimal bounds.

A compact dual layer conformal wearable quad band antenna is proposed for wireless body area network applications. The proposed button like patch antenna resonates at 2.5 GHz (industrial, scientific, and medical bands)/3.6 GHz sub six 5G band/5.75 GHz (wireless local area network/ISM band)/ and 9.8 GHz (X band) frequencies. The circular textile antenna is constructed with jean and polydimethylsiloxane substrate having a slotted ground of radius 10 mm and thickness 1.5 mm. The simulated gains obtained at the operating bands are 1.85/2.03/1.49/3.27 dBi, respectively. The designed antenna’s directed radiation pattern assures reduced backward radiation to body tissue. The specific absorption rate (SAR) analysis for the antenna at multiple resonant frequencies has also been reported, which are well below the SAR threshold of 1.6 W/kg for 1 gm of tissue, indicating that the model works adequately for wearable applications. The experimental characterization on- and off-body of the fabricated antenna validates the simulated results.

The presence of obstacles in the propagation path is a critical factor in air-to-ground (AG) communication. The behavior of wireless signal propagation depends on several variables, such as frequency, building height, elevation angle, and street design. This paper aims to compare the three established line of sight (LOS) probability model based on actual site data, including the building geometry in suburban environment. The comparison between these three models using the site data provide a guideline for selecting the LOS probability model based on the optimistic and pessimistic predictions. The shadowing loss was evaluated at frequencies 2 and 3.5 GHz with an elevation angle of 20° in two suburban locations at Universiti Tun Hussein Onn Malaysia. Three prediction models, ITU-R P.1410-5, Holis and Pechac, and Pang et al., available in the literature were used to identify and compare the line-of-sight probability. By focusing on the shadowing model in suburban area, the guideline for optimizing LOS communications or navigation in these challenging environments can be developed. The finding highlights the importance of considering building height in AG communication for network performance evaluation and design.

In this paper, on–off switching digitization of a W-band variable gain power amplifier (VGPA) with above 60 dB dynamic range is introduced for large-scale phased array. Digitization techniques of on–off switching modified stacking transistors with partition are proposed to optimize configuration of control sub-cells. By the proposed techniques, gain control of a radio frequency variable gain amplifier (VGA) could be highly customized for both coarse and fine switching requirements instead of using additional digital-to-analog converters to tune the overall amplifier bias. The designed VGA in 130 nm SiGe has achieved switchable gain range from −46.4 to 20.6 dB and power range from −25.0 to 15.7 dBm at W band. The chip size of the fabricated VGPA is about 0.31 mm × 0.1 mm.

This article presents an ultrawide bandpass filter structure developed along a notch band using a small rectangular impedance resonator. The proposed filter structure consists of a coupled rectangular resonator (CRR), open stub, and composited split ring resonator (CSRR) at the bottom of the structure. In-band and out-of-band properties are improved by the CRR and open stub. The notch band is obtained by placing CSRR below the rectangular resonator. A filter with a compact size of 0.15 × 0.10 λg is obtained at a lowered cutoff frequency of 3.0 GHz, where λg is the corresponding guided wavelength. The proposed structure has been constructed on 5880 Rogers substrate with a thickness of 0.787 mm and a dielectric constant of 2.2. Additionally, equivalent lumped parameters were obtained, and a lumped equivalent circuit was created to explain how the suggested filter operated. The Electromagnetic (EM)-simulated results are in good agreement with the circuit-simulated and measured result. The various machine learning approaches such as artificial neural network, K-nearest neighbour, decision tree, random forest (RF), and extreme gradient boosting algorithms are applied to optimize the design, in which RF algorithms achieve more than 90% accuracy for predicting the S parameters of the ultrawideband filter.