In [A. Capozzoli, C. Curcio, A. Liseno, MMS, Pizzo Calabro, Italy, 2022], the problem of modeling a source/scatterer using an equivalent radiator has been addressed and an approach has been given and numerically assessed.

Once dimensioned the radiating panel, a practical implementation can be provided by a non-uniform array. The element positions should be chosen so that the array is capable to approximate, with an adequate accuracy, the fields radiated by the equivalent radiator. Here, the array element positioning is performed by exploiting a quadrature rule which takes into account that the singular functions supported on the region of interest associated to the most significant singular values of the radiation operator are related to those supported on the equivalent panel by a radiation integral. The quadrature rule enables also to choose a set of weights which are essential in the definition of the element excitation coefficients from the knowledge of the source distribution on the equivalent panel. For simplicity, a one-dimensional problem with a Legendre quadrature rule is considered. The approach is numerically assessed by checking the capability of the array to radiate, with a satisfactory degree of accuracy, the singular functions associated to the region of interest.

A low-profile wideband circularly polarized (CP) metasurface antenna is demonstrated for C-band applications. The metasurface consists of 4 × 4 square patches with Z-shaped slots. Characteristic mode analysis is used to investigate the modal behavior of the metasurface, and a pair of degenerate modes is chosen as the operating modes. The CP radiation is realized by exciting a pair of degenerate modes of the metasurface through a slot antenna, which is used as a feed structure with a 90° phase difference. The CP bandwidth is further widened by combining the resonance modes of the metasurface and slot antenna. The measured results show that the −10 dB impedance bandwidth of the antenna is 3.47–4.76 GHz, and the 3 dB axial ratio bandwidth is 3.5–4.9 GHz with a peak gain of 6.9 dBic. Moreover, the antenna exhibits well left-hand CP radiation performances with a low profile of 0.046λ0.

This paper presents the design and implementation of a broadband down-converter system using the AWR (Advancing the Wireless Revolution) modeling and Microwave Office tool. The radio frequency (RF) signal coming to the antenna interface requires a frequency down-converter to be lowered to the intermediate frequency (IF) band. It includes mixing blocks, oscillators, amplifiers, step attenuators, isolators, and filters. The input frequency band (RF) is 8250 ± 250 MHz, while the output frequency (IF) band is 720 ± 200 MHz. The gain dynamic range of the circuit is expanded through the use of digital attenuators. It is a superheterodyne down-conversion circuit, combining the IF band to produce the desired RF spectrum in one pass. Two phase-locked oscillators are used at the local oscillator port of the mixer, one providing a single frequency, while the other has a programmable frequency synthesizer with 1 MHz steps in the frequency range from 7280 to 7780 MHz.

This paper presents an integrated power amplifier (PA) following the orthogonal load-modulated balanced amplifier (OLMBA) topology. The fixed-phase prototype in this paper is implemented with 22 nm complementary metal oxide semiconductor (CMOS) fully depleted silicon-on-insulator (FDSOI) process. The proposed PA operates at 26 GHz frequency range, where it achieves 19.5 dBm output power, 16.6 dB gain, 15.7% power added efficiency, and 18.3 dBm output 1-dB compression point ($P_{\rm 1\,dB}$). The PA is also tested with high dynamic range modulated signals, and it achieves, respectively, 11.4 dBm and 4.9 dBm average output power (Pavg) with 100 MHz and 400 MHz 64-QAM third-generation partnership project/new radio frequency range 2 signals, and 14 dBm Pavg with 0.6 Gb/s (120 MHz) single carrier 64-QAM signal, measured at 26 GHz and using −28 dBc adjacent channel leakage ratio and −21.9 dB (8%) error vector magnitude as threshold values. The proposed OLMBA is also compared to a stand-alone quadrature-balanced PA. Modulated measurements show that the stand-alone quadrature-balanced PA has better linearity in deep back-off, but the OLMBA has better efficiency.

This paper presents a compact and ultra-wideband high-efficiency microwave rectifier for wireless power transmission (WPT) applications. The input-matching-network utilizes a compact asymmetric coupled transmission line structure, contributing to wideband performance. The rectifier adopts a voltage-doubler topology, resulting in a smooth input impedance across a wide bandwidth. The working principle of the asymmetric coupled transmission line matching network is analyzed. Simulation and measurement are conducted on the proposed rectifier. The fabricated prototype demonstrates a wide bandwidth of 162.5% (0.3–2.9 GHz with the power conversion efficiency (PCE) exceeding 60% at an input power of 18 dBm. Even at an input power of 10 dBm, the measured PCE remains above 50% over the working band. The proposed ultra-wideband rectifier shows promising potential for WPT applications including wireless powering of low-power electronic devices and sensors.

This paper proposes a design method for designing a wideband filtering power amplifier (PA) based on terminated coupled line structure (TCLS). This method generates four transmission zeros and three transmission poles by loading stepped impedance resonator and short-circuit stubs on the four ports of TCLS, which greatly optimizes the in-band return loss and stopband suppression of the output matching network. In addition, the effective suppression of the second harmonic also increases the efficiency of the PA. In order to verify the effectiveness and superiority of this design method, a wideband bandpass filtering PA is designed and manufactured in 2.9–3.7 GHz. Measurement results show that the saturated output power is from 40.1 dBm to 41.2 dBm, the drain efficiency is greater than 60.3%, and the gain is 10–11.2 dB.

The mining industry is heavily dependent on energy-intensive processes, such as rock breakage, which leads to significant operational costs. This paper explores microwave-assisted rock breakage as an innovative method to enhance the efficiency of comminution within the mining industry. It introduces a system that employs a Klystron microwave power source with a maximum output of 7.5 MW, using a $\mathrm{TM}_{010}$ single-mode cavity at 3 GHz, to channel energy inside a specially designed rock cavity. The paper emphasizes the importance of designing an efficient microwave cavity for this system, focusing on the cavity’s design and simulation. Through both simulated results (using HFSS software) and experimental observations, the study reveals the promising application of microwave technology in the field of mining. The simulated frequency response of the designed cavity (S11) is −22 dB, it demonstrates significant potential for reducing both energy consumption and associated costs. Additionally, the designed cavity is fabricated from aluminum and filled with polyether ether ketone material. The measured frequency response (S11) of the cavity at 3 GHz is −17 dB.

This paper presents a compact broad dual-band rectifier based on a transmission line matching network. This method improves the overall impedance matching performance over two bands, and improves bandwidth of the rectifier’s efficiency. A π-type direct current filter with excellent harmonic suppression performance is proposed. The multi-section transmission line used as the dual-band input impedance matching network is analyzed to achieve an arbitrary frequency ratio. A rectifier is designed and implemented using a three-stage transmission-line matching network. Simulation and experimental results show that a dual-band rectifier is successfully performed with the measured power conversion efficiency (PCE) of 75.7% and 76.3% at 0.915 and 2.45 GHz, respectively. Additionally, the rectifier exhibits bandwidths of 0.48 and 0.25 GHz when the PCE exceeds 70%. Significant enhancement of bandwidth over conventional rectifiers is demonstrated.

The rapid expansion of digital media platforms and their growing user base in the wireless industry necessitate communication systems to provide information at high speeds with reliable connections. Therefore, wireless communication systems with a single antenna cannot accomplish these requirements. Consequently, the access and utilization of multi-input multi-output (MIMO) antennas are becoming more common in contemporary high-speed transmission systems. This article covers the fundamentals of MIMO antenna operation, the metrics for MIMO antenna performance parameters, and the design methodologies for specifying the three most commonly used antennas (two-port, quad-port, and eight-port). Additionally, it discusses their ability to improve channel capacity significantly. It focuses on designing MIMO antennas with ultra-wideband (UWB) for 5G systems operating between 1 and 27 GHz and millimeter-wave (mmWave) bands from 30 to 100 GHz. This article is valuable for researchers interested in developing MIMO antennas for diverse applications. It compiles advanced methods related to materials, advancements, challenges, and state-of-the-art technologies used in the design of high-performance MIMO antennas. We concluded that antennas that operate at mmWave frequencies have small dimensions and suffer from isolation problems in the MIMO formation. In contrast, antennas operating below 6 GHz are large and do not suffer from isolation problems.

This research article represents the design of a simple, smaller, and novel frequency reconfigurable patch antenna for 5G communication using PIN diodes. This antenna operates in both mid-5G and high-5G bands. The antenna is intended to operate in eight distinct modes with three PIN diodes in 5G wireless communication covering 27.46–50 GHz of high-5G band (range n257/n258/n260/n261/n262) and frequencies of the 3–6 GHz of mid-5G band (range n77/n78/n79/n46). The antenna has an overall size of 20 mm × 25 mm × 1.6 mm and is placed upon a low-cost FR4 substrate. A higher radiation efficiency from 75% to 98% is achieved in all the different modes. The resonant frequencies are around 3.46, 4.43, 5.83, 31.8, 35.5, and 46 GHz in different modes of operation. Different switching statuses have been carried out in this research work and their performances have also been illustrated in the form of surface current distribution in different resonant frequencies. The simulated and measured results are compared to highlight its proposed design operation.

A bandwidth expansion strategy for ultra-wideband power amplifiers (PAs) is presented in this letter by adopting a parallel impedance matching architecture. This design strategy can effectively reduce the impedance conversion ratio between the load and the target impedance of the PA, thereby providing a feasible solution for broadband impedance matching. Subsequently, a commercially available 10 W gallium nitride device and a two-stage Wilkinson power divider network are combined to achieve the verification of the proposed theory. The results of the measurement show that within the target frequency band of 0.9–3.9 GHz, 58.5–71.2% of the drain efficiency and 9.1–12 dB of gain can be achieved with a saturated output power of 39.1–42 dBm.

This paper proposes a wideband four-element multiple-input multiple-output (MIMO) antenna operating in the millimeter-wave frequency band for 5G communications from 24.37–39.44 and 45.09–50.62 GHz. The antenna design has been realized using Rogers 5880 substrate and consists of a T-shaped strip that is attached to the top of a 50 Ω feeding line. Two microstrip lines are affixed at the terminal points of T-shaped strip and bent toward the feeding structure. These bent strip lines are then extended by joining two additional L-shaped microstrip lines. On the back, there is a partial defective ground plane featuring a rectangular slot and a thin strip line located at its center. The dimensions of the proposed single element and MIMO antenna are 0.933λ × 0.933λ × 0.024λ and 1.865λ × 1.865λ × 0.024λ, respectively (at 28 GHz), while the edge-to-edge distance between the radiation elements of the MIMO antenna is 4.0 mm. The design incorporates an efficient passive fan-shaped decoupling structure to decrease coupling between antenna elements. Simulations and experimental results show good agreement with each other. For all resonant frequencies the measured peak gain is greater than 4.85 dBi, radiation efficiency is over 90%, diversity gain is greater than 9.5, ECC is less than 0.025, TARC is less than -10 dB and CCL is below 0.4 bits/s/Hz. The proposed MIMO antenna, with its wide bandwidth, high gain, high inter-port isolation, and high efficiency characteristics, can be used for 5G wireless communication applications.

A system-in-package for a wideband digital radar, in D-band, requires broadband, high-gain antennas combined with broadband chip-to-package and package-to-printed circuit board (PCB) interconnects. This paper demonstrates a wideband, low-loss quasi-coaxial signal transition, and a novel electric split ring resonator (eSRR)-based antenna-in-package (AiP) with a modified reflector concept, for improved gain, in embedded wafer level ball grid array (eWLB) technology. A complete chip-to-package-to-PCB interconnect is also demonstrated by combining the quasi-coaxial transition with a chip-to-package interconnect. The quasi-coaxial signal transition has the largest impedance bandwidth among ball grid array-based quasi-coaxial signal transitions. For the modified reflector concept, a horn-shaped cavity is micromachined in the PCB substrate and remetallized with aerosol-jet printing, placing the reflector 0.25λ from the antenna. The antenna gain is improved with up to 5.3 dB. The AiP with the horn-shaped reflector is the single element with the highest gain, in eWLB technology, above 100 GHz.

This study proposed an effective and sustainable technique for the curing of carbon fiber reinforced polymers (CFRPs) using microwaves. The method involves applying a metallic resonance coating layer to envelop the CFRP composite’s surface. Next, the composite is positioned within a multi-mode cavity, which is used as an applicator, and is powered by four 250 W solid-state power amplifiers. To ensure precise control over the heating pattern and achieve uniform heating of the composite, a sophisticated control algorithm is developed. This algorithm can independently regulate the phase, power level, and frequency of each power amplifier. The experimental results confirm the effectiveness of this proposed approach in achieving precise control over the microwave-based curing process for CFRPs.

This paper proposes fractal-inspired array antennae for wideband applications. The proposed antennae have a resonance frequency range of 20–40 GHz. The modified fractal antennae are fabricated with a height of 1.6 mm, substrate width, and length of 100, 50, 25, and 18.75 mm2, and a simulated result shows that the gain is increased to 11.04, 11.9, 8.4, and 6 dBi, and the designed antennae radiate power with directivity of 11.3, 13.4, 9.29, and 7.17 dBi concerning proposed designs A, B, C, and D, respectively. The proposed antennae with 5G New Radio (NR) bands have more radiation concerning resonate frequencies in the 20–40 GHz range with Φ = 0°, Φ = 90°, and θ = 90°. Moreover, the bandwidths for applications covered in the 5G NR and sub-6G are 1.92, 0.73, 0.7, 2.4, 1.3, 5.3, and 1.26 GHz, and 3.4, 3.7, 2.67, and 4.65 GHz, and 2, 3.5, and 1.57 GHz, and 2.5, 1.5, and 1.0 GHz with the maximum return loss of 37 dB, 32.8 dB, 31.2 dB, and 23 dB with corresponding resonate frequencies as 21.5, 27.6, 33, and 27.6 GHz concerning designs A, B, C, and D, respectively. The proposed antennae have been implemented and validated using Computer Simulation Technology (CST), Vector Network Analyzer (VNA), spectrum analyzer, and power sensor.

This paper presents a Ka-band series single-pole double-throw (SPDT) switch circuit realized in substrate-integrated coaxial line (SICL) environment for time division duplex operation. It is designed with a low-cost printed circuit board (PCB) technique. The size of the proposed circuit is $3.1\lambda_{g} \times 5.9\lambda_{g}$, where λg is the guided wavelength at the center frequency of 27.75 GHz. In this circuit, a SICL-based SPDT switching circuit is proposed with radio frequency (RF) isolation network where the shunt connection of butterfly stubs is in an asymmetric stripline environment. The proposed circuit exhibits less than 2 dB insertion loss at 27–27.9 GHz and less than 2.5 dB insertion loss at 27–28.5 GHz. The design offers good impedance matching in the Transmit (Tx) and Receive (Rx) channels from the common Tx/Rx input channel, along with more than 24 dB isolation between ON and OFF state output channels. The proposed circuit is suitable for millimeter-wave communication systems.

In this paper, the development and designing of angle-independent metamaterial microwave absorbers are presented. The unit cell consists of two concentric circle that are linked by consolidated resistors. The absorber is built on a dielectric substrate (FR4) with a thickness of 3.2 mm (λ/0.07) and a dielectric constant of 4.3. The wideband absorption is acquired in the range of 2.8 to 10.42 GHz with a wide band of 7.62 GHz with absorptivity above 90%. In the area of interest, a flat band is obtained, and to examine the current distribution and electric field in the respective region, two peaks are considered at a frequency of 3.66 and 9.54 GHz, with maximum absorptivity of 99.99% and 99.44%, respectively. The presented absorber is examined under different angles for phi and theta variation. From the phi variation, it is observed that for all the angles, absorptivity does not vary, which confirms that the absorber is acting as an angle independent. The fabricated sheet consists of an array of a unit cell, which is examined inside the anechoic chamber with the help of two horn antennas and vector network analyzer. The tested and simulated results are compared, and it was observed that they are close in their agreement. At the end of the manuscript, the presented and already reported arts are compared, and it is observed that the presented one operates for the low frequency with higher bandwidth. The presented absorber can be practically used for defense applications for Radar Cross Sections reduction.

The design and development of a microstrip-based planar ultra-wideband (UWB) bandpass filter (BPF) with single/multiple interference rejection capability is presented. The proposed BPF structure is developed based on the broadside coupled mechanism of microstrip/coplanar waveguide (CPW). The BPF has microstrips and short-circuited CPW capacitively coupled through the substrate. The basic frequency response generated from this geometry covers the necessary UWB spectrum (3.1–10.6 GHz) and possesses appreciable characteristics due to dual transmission zeros at either passband boundary. Multiple resonators are embedded in the basic BPF structure to develop passband notches to circumvent unnecessary interferences. A low-pass filter is later integrated into geometry to extend the upper stopband. The proposed structure is compact and covers an area of only 14 × 11.4 mm2.

This paper presents a substrate-integrated waveguide (SIW) differential antenna for full duplex applications. The proposed antenna consists of two square SIW cavities named as outer and inner. The inner cavity is nested into the outer cavity. The outer cavity is differentially excited with a pair of coaxial feed lines, while the inner square patch is orthogonally excited with another pair of differential coaxial feed lines. This orthogonal feeding arrangement results in high isolation between the differential ports. The modified hybrid TE130/310 mode of the outer cavity radiates through a pair of arc-shaped slots at 9.35 GHz, while the TM01 mode of the inner square patch is responsible for the radiations at 8.65 GHz. The proposed antenna prototype is fabricated and measured for validation. Moreover, the designed antenna has a front-to-back ratio better than 22 dB and measured maximum gain values of 6.1 dBi and 7.6 dBi at 8.65 GHz (Port 2 ON) and 9.35 GHz (Port 1 ON), respectively.

In the proposed paper, a novel design and realization of a wide-band, oblique angle-insensitive metamaterial absorbers are presented. The absorber is designed to work over a wide range of frequencies, making it suitable for Ku-band applications. To get wide band absorption, a novel SM-shaped design with a square-tooth circular ring resonator structure is designed efficiently. The unit cell structure is designed with a dielectric substrate (FR4) with a thickness of 3.2 mm (0.16λ0), where λ0 is the wavelength of free space. The novel design of this configuration leads to wideband absorption with respect to a conventional absorber. Several physical parameters are also investigated, such as the dielectric constant, permittivity, permeability, impedance, and negative refractive index. The simulation and experimental results show from 13.60 to 16.14 GHz with 99.1% absorption, which is excellent agreement. The analysis of the proposed design indicates that it possesses the remarkable feature of being insensitive to polarization while also exhibiting high absorption even when the angle of incidence varies. For both the simulation and experiment, results are consistent with a frequency range of 13.60–16.14 GHz for normal incidence. Almost perfect absorption works well for solar cells, EM detection, and imaging applications.