Electronic measurement systems in the THz frequency range are often bulky and expensive devices. While some compact single-chip systems operating in the high millimeter-wave frequency range have recently been published, compact measurement systems in the low THz frequency range are still rare. The emergence of new silicon-germanium (SiGe) semiconductor technologies allow the integration of system components, like oscillators, frequency multipliers, frequency dividers, and antennas, operating in the low THz frequency range, into a compact monolithic microwave integrated circuits (MMIC), which contains most components to implement a low-cost and compact frequency-modulated continuous-wave-radar transceiver. This article presents a single transceiver solution containing all necessary components. It introduces a $0.48\,\mathrm{THz}$ radar transceiver MMIC with a tuning range of $43\,\mathrm{GHz}$ and an output power of up to $-9.4\,\mathrm{dBm}$ in the SG13G3 $130\,\mathrm{nm}$ SiGe technology by IHP. The MMIC is complemented by a dielectric lens antenna design consisting of polytetrafluoroethylene, providing up to $39.3\,\mathrm d\mathrm B\mathrm i$ of directivity and half-power beam widths of 0.95∘ in transmit and receive direction. The suppression of clutter from unwanted targets deviating from antenna boresight more than 6∘ is higher than $24.6\,\mathrm d \mathrm B$ in E- and H-Plane.

In this paper, a capsule endoscopy system with a sensing function is proposed for medical devices. A single-arm spiral antenna is designed for data transmission and is combined with the voltage controlled oscillator to achieve sensing capabilities. The designed antenna operates at a 900 MHz industrial scientific medical band. By establishing a three-layer cylindrical model of the stomach, it was concluded that the antenna in the stomach has a high peak gain of −1.1 dBi. Additionally, the antenna achieved a −10 dB impedance bandwidth of 5%. The capsule endoscopy was experimentally measured in both actual stomach and simulated environments. The maximum working distance of the capsule endoscope was measured to be 6.8 m. Additionally, the proposed capsule endoscope was tested for its sensing function using solutions with different dielectric constants. Finally, it was confirmed through link analysis that it has good communication capabilities. The results and analysis confirm that the proposed capsule endoscope can be used for examining gastric diseases.

An E-band Cassegrain switched beam high-gain antenna concept for 5G backhauling systems is proposed in this article. The antenna requirements target the compensation of small misalignments (within ±1 degrees in both azimuth and elevation planes) in E-band backhauling links due to adverse weather conditions or thermal deformations. The intended antenna is able to realize beam-switching operations by using a feed-array architecture based on a 7 × 7 array of cavity-backed magnetoelectric (ME) dipoles, where every element is capable of providing a steering of ±0.33 degrees in both the elevation and the azimuth planes. The ME dipole illuminators combined with a Cassegrain reflector provide a gain of 52 dBi within the whole scanning range. Besides, they can be easily integrable with the front-end modules, thus being an easily implementable and low-cost alternative to other more complex solutions based on horns or lens antennas.

In this article, different 2D and 3D mask styles for synthesizing large array pattern shaping to meet the requirements of modern applications are realized. The composition of the different beam pattern shaping is achieved by comparing the array factor with the proposed masks whose details (upper and lower borders) are predefined according to the designer. The generated pattern shapes are as follows: unscanned 2D single-pencil beam, scanned 2D pencil beam, 2D multi-beam scanning, 2D wide flat beam with little ripple, unscanned 3D single-pencil beam, 3D multi-beam scanning, and footprint (or contour) pattern for linear and planar arrays. The process of constructing these patterns is followed by predicting the amplitude-only weights (i.e., the phase weighting is considered zero in all computations) of the elements using the particle swarm optimization algorithm. In all proposed masks, different sidelobe levels are controlled, ranging from −20 to −100 dB. Also, the radiated beamwidth is controlled, ranging from 0.1334 rad (7.6 deg.) to 0.4 rad (23 deg.). The analysis and construction of linear and planar array arrangements depend on the formulation of antenna array theory through the implementation of the proposed (estimated) equations using MATLAB code. The simulation results showed the effectiveness of the proposed methods in controlling the pattern shape according to the required modern trends.

In this study, tunability of the electromagnetically induced transparency (EIT)-like transmission window by low-volume dielectric loadings is presented both numerically and experimentally in S-band. The EIT-like transmission behavior is obtained by a metamaterial, composed of an electric resonator and a closed-ring resonator patterned on a dielectric substrate. The frequency tuning is obtained by two applications called horizontal sliding application (HSA) and vertical sliding application based on sliding of the low-volume loadings from the edges to geometric center (i.e., inward). For both applications, the frequency tuning has been investigated for dielectric loadings which have relative permittivity of 2.2, 3, 4.5, and 6.15. The results reveal that the proposed sliding applications are effective on tuning the transmission peak frequency. An achieved 1136 and 971 MHz absolute spectral shifts and corresponding 6.34% and 5.41% absolute sensitivities by simulations and measurements, respectively, are the best results which are obtained for HSA at 5 mm shift value. Moreover, 14.67% sensitivity is obtained in simulations for the complete dielectric loading on the resonator in response to the increase in refractive index from 1 to 1.5. It is believed that the proposed applications will contribute to the existent sensing studies.

An absorptive reconfigurable bandstop filter (BSF) with compact size and ultra-wide frequency tuning range using distributed lossy resonators is presented. In each reconfigurable bandstop resonator, a varactor and a PIN diode are utilized as the control and absorption devices. When the PIN diodes are in off and on states, the upper and lower frequency tuning ranges of stopbands can be obtained, respectively. Therefore, the ultra-wide total frequency tuning range which is the combination of the upper and lower frequency tuning ranges can be realized. Meanwhile, the stopband frequency and bandwidth tuning can be independently controlled by bias voltages. The resistances in the varactors and PIN diodes can dissipate the electromagnetic power and thus result in absorptive stopband without using extra absorptive circuits. The stopband suppression level and stopband absorption ratio are proportional to the number of distributed lossy resonators. For demonstration, an absorptive reconfigurable BSF prototype using six pairs of distributed lossy resonators is designed and fabricated. The measured total frequency tuning range is 3.03–6.39 GHz (71%) with the suppression level of 20 dB, while the frequency tuning range with the suppression level of 10 dB is 2.04–6.39 GHz (103%).

This paper investigates if there is an optimum design of loaded-line phase shifters with respect to phase shift/loss figure of merit (FOM) and linearity. The investigation was performed by comparing six loaded-line phase shifters that were implemented in printed circuit board (PCB)technology with shunt-loaded hyperabrupt varactor-diodes. It was demonstrated that the hyperabrupt varactor’s C-V characteristics must be modeled with high accuracy to predict the nonlinear behavior. A polynomial varactor model was employed and experimentally validated. To extend the range of investigated parameter values, the extracted model was scaled and evaluated further in a circuit simulator. The investigation reveals that for a given varactor-capacitance, the phase shift/loss FOM is improved if the varactor-capacitance is evenly distributed and the unit cell length is much shorter than a quarter wavelength. The study demonstrates that the phase shift/loss depends mainly on the distribution of varactor-capacitance and Q factor. The intermodulation (IM) distortion is primarily proportional to the total varactor-capacitance per unit cell. The study also revealed that an increase in the varactor’s Q factor results in higher IM. Therefore, it is a trade-off between low loss and low IM.

This paper presents a three-stage E-band low-noise amplifier (LNA) fabricated in a 28-nm Complementary Metal Oxide Semiconductor High-Performance Compact Plus process. The proposed E-band LNA achieves a peak gain of 16.8 dB, exhibiting a gain variation of less than ±0.5 dB across the frequency range of 67.8–90.4 GHz. The measured 3-dB gain bandwidth spans from 64 to 93.8 GHz, and the minimum measured noise figure (NF) is 3.8 dB. By employing a one-stage common-source with a two-stage cascode topology, the proposed E-band LNA demonstrates competitiveness in terms of gain flatness and NF when compared to recently published E-band CMOS LNAs.

This work introduces a novel compact ultra-wideband (UWB) antenna designed for wearable applications, employing a bioinspired structure and machine learning (ML) techniques to achieve exceptional performance in the 3.10–10.42 GHz range. The antenna is fabricated by positioning conductive fabric on a polydimethylsiloxane polymer of 1 mm thickness to augment high flexibility and durability. Additionally, it pioneers integrating a complete ground plane to mitigate back radiation toward the human body, presenting a compact (35.5 × 30.5 × 1 mm3) UWB antenna design compliant with IEEE 802.15.6 standards. The design methodology includes using bandwidth enhancement techniques such as chamfering edges, slots, and adding stubs in the feed, along with applying ML to optimize the antenna’s dimensions for desired return loss characteristics. The proposed antenna demonstrates exceptional resilience to human body loading and physical deformation. The simulation and measurement results have good agreement. The K-nearest neighbour method beat the other ML algorithms maximum accuracy of 99.62% to predict the S11. According to the author’s best knowledge, this is the first compact UWB antenna with full ground specified by IEEE.802.15.6 with ML reported.

This paper outlines an experimental demonstration of an envelope tracking (ET) technique applied to a kilowatt-level single-ended solid-state power amplifier (SSPA), aimed at enhancing the charging efficiency of superconducting radio frequency (SRF) cavities by reducing reflection power while maintaining a high degree of efficiency. The technique is particularly designed for the pulsed operation of the European Spallation Source (ESS) at a nominal frequency of 352 MHz, with a 5% duty cycle and a pulse width of 3.5 ms. The study introduces an optimal charging scheme using a solid-state-based amplifier to maintain high efficiency, allowing for power ramp-up while minimizing reflections from SRF cavities and optimizing SSPA efficiency. A fast envelope tracking power supply (ETPS) system is implemented for the approximately 300 ms charging time required by the SRF cavities at ESS. The ETPS system, demonstrated on a single module as a proof-of-concept with scalability potential to a 400 kW power station, indicates an overall average efficiency of 70% and a 24% energy saving over traditional vacuum-tube based amplifiers. This demonstrates the ET technique’s effectiveness at the kilowatt level for efficient SRF cavity charging with reduced reflection, offering significant efficiency and energy savings.

By combining the technique of energy selective surface and frequency selective rasorber, an energy selective rasorber is proposed, which performs selective energy protection in the low communication frequency band (0.8–2 GHz) and wave-absorbing property in the high-frequency band (6–18 GHz). The design consists of two layers, of which the bottom one contains a lumped diode structure for energy selection function in the transmission band, while together with the top layer, they perform a wideband wave absorbing function. The simulated and measured results agree well with each other, and both show good absorption in 6–18 GHz and energy-selective property around 1.86 GHz. That is, when the incident power changes from −30 to 14 dBm, the reflection coefficient changes from below −22 dB to above −2 dB, while the transmission coefficient changes from above −3 dB to below −17 dB.

With the rapid development of communication technology, the researches of multi-band filtering circuits have become more and more important. Multimode resonator (MMR) is one of the vital methods to provide multi-resonant modes within a single design. In this paper, a dual-band ultra-wideband bandpass filter (UWB-BPF) using stepped impedance stub-loaded resonators (SI-SLR) is presented. The main advantage of using SI-SLR is to have better performance with multimode behavior and more parameters to control resonant modes. SI-SLR combines the advantages of SIR and SLR structures, which gives a compact, high-performance multiband filter. The proposed filter design has compact size, sharp and flat response with low insertion loss (IL), low return loss (RL), and high band-to-band rejection. The filter is designed for UWB communication in wireless body area networks and fabricated on Arlon substrate with relative permittivity ${\varepsilon_{\textrm{r}}} = 3.25$, thickness $0.8\;{\textrm{mm}}$. The resulted dual-bands are centered at $4{\textrm{ GHz}}$ and $8.3{\textrm{ GHz}}$ with fractional bandwidths $37{\textrm{% }}$ and $48{\textrm{%}}$. The simulation was carried out using CST Microwave Studio. The filter provides good passband performances, with IL 0.49 dB and 0.31 dB at the center frequency of lower and higher bands, respectively. The band-to-band 40 dB rejection is realized by adding circular spiral at the input/output of the filter.

In this paper, a wearable antenna array based on a 9 × 3 artificial magnetic conductor (AMC) array is proposed with the characteristics of compact, low profile, low specific absorption rate (SAR), high front-to-back ratio (FBR) and high gain for wireless body area network (WBAN) bands. The proposed wearable antenna consists of a four-element array and an AMC array. The size of antenna array loaded AMC is 137.7 × 45.9 mm2. The dielectric substrate of the antenna and the AMC structure are made of 0.1 mm liquid crystal polymer material, which is flexible and low profiled. The antenna operates from 5.62 to 6 GHz after the AMC structure is loaded. The gain increases by 3.23 dB, reaching 12.03 dB at 5.8 GHz. And the FBR value is raised by 26.04 dB. The highest SAR value of the simulated antenna on the human model is 0.0496 W/kg, far less than the US federal or EU requirements. After constructing and testing the antenna, the outcomes of the tests agreed with the results of the simulation. The flexible antenna array with AMC structure has good prospect in WBAN applications.

A systematic design approach is presented for the design of broadband high-efficiency power amplifiers (PAs) by combining an improved ring-resonant filter matching network with a series of continuous modes. The improved ring-resonant matching network presented can effectively enhance out-of-band attenuation and sharp roll-off characteristics by adding a compensation structure with parallel stub. To verify the proposed design theory, a 10-W GaN HEMT device is designed and fabricated. The test results indicate that from the operating frequency band of 0.55−3.3 GHz with a relative bandwidth of 142.9%, a saturated output power of 38.5−42 dBm, drain efficiency of 58.2−70.3%, and a gain of 8.5–12 dB can be achieved under 3 dB gain compression, indicating the rationality of the design theory.

In this article, a low phase noise signal source to be used as local oscillator in pulse Doppler radio frequency (PDRF) sensor is proposed. Innovative design techniques for realization of the low phase noise frequency source using phase-locked loop (PLL) and dielectric resonator (DR) are presented. Qualitative investigations have been carried out on the effect of phase noise in PDRF sensor performance. An X-band vibration resistant PLL-based frequency source with phase noise better than −95 dBc at 1 kHz frequency offset has been designed here. It also presents the design of a 7.6 GHz low phase noise, vibration resistant DR oscillator. Systematic analysis of the key design aspects, their thermal-vibrational stability, and ease of integration with hybrid microwave integrated circuits have been disclosed. A prototype board is fabricated, assembled in a compact mechanical enclosure of dimension 55 × 55 × 15 mm3. Finally, developed module is experimentally validated under 7.6 g rms magnitude random vibration test in three axes and compared results with other state of-the-art similar works. The comparison clearly shows the merit of present research work over other similar existing works.

A novel thinned antenna element distribution for cancelling grating lobes (GLs) as well as for reducing phase shifters (PSs) is presented for a two-dimensional phased-array automotive radar application. First, an efficient clustering technique of vertical adjacent elements is employed with array thinning for a PS reduction of 66.7%. In the proposed distribution, several single-element radiators (non-clustered antenna elements) are placed in the vertical direction with specific spacing in a grid of 16 × 12 (192) elements with λ/2 pitch. This disrupts the periodicity of phase-centers after element-clustering and takes a role as steerable GL canceller with capabilities of tracking and nullifying the GL at any scan angle. The proposed distribution enables beam steering up to ±60° in the azimuth plane, as well as ±25° in the elevation plane with cancelled GL and sidelobes. Furthermore, the proposed distribution has been efficiently calibrated with all elements activated by introducing the code division multiple access technique. To the best of the authors’ knowledge, this work represents the first fully calibrated state-of-the-art thinned distribution phased-array including a novel steerable GL canceller to track and nullify GLs.

A wideband antipodal Vivaldi antenna has been designed and optimized. A slight improvement is obtained by employing multiple metalense based on circular split-ring resonators to maximize the antenna gain with the maximum bandwidth. The designed antennas have been fabricated and characterized, showing good agreement with simulations. The maximum measured gain is $G = 12\;{\textrm{dB}}$, and the −10 dB bandwidth is from $f = 3\;{\textrm{GHz}}$ to $f = 13\;{\textrm{GHz}}$.

This paper presents the application of a substrate-integrated waveguide (SIW) for the design of a leaky-wave antenna (LWA). The antenna radiates through a wide slot in the top wall of the SIW structure in the forward direction. The effective width of the slot is varied by changing capacitances of two arrays of varactors connected between slot edges and inserted conducting strips. The radiation pattern of the antenna is by this way controlled by DC bias, which sets the capacitances of varactors. The maximum radiation direction in elevation can be varied within 35° by changing the DC bias from 2 to 12 V. This elevation angle is measured from the broad side direction perpendicular to the antenna substrate. The measured antenna characteristics are in accord with those predicted by simulation. The antenna can be simply fabricated by a planar circuit board technology.

This paper presents a method for measuring whole-body specific absorption rate (WBSAR) of millimeter-wave base stations (BSs) in a reverberation chamber (RC). The absorbed power in the phantom from the equipment under test (EUT) and hence WBSAR is determined as the difference between the total radiated power with and without the phantom. A chamber transfer function is determined and used to include only the absorption in the phantom due to direct illumination from the EUT, i.e., excluding absorption due to the RC multipath reflections. The measurement method was evaluated at 28 GHz using a horn antenna and a commercial massive multi-input–multi-output BS. The experimental results are in good agreement with simulations. The proposed method allows for measurements of WBSAR within 3 minutes, which is much shorter than traditional approaches. The method is suitable for compliance assessments of BS products with the International Commission on Non-Ionizing Radiation Protection 2020 electromagnetic field exposure guidelines, which extend the applicability of WBSAR as basic restrictions up to 300 GHz.

This paper presents the design and analysis of a compact eight-port multiband multiple-input–multiple-output (MIMO) antenna for 5G smartphones. The proposed antenna structure is designed using meandering elements, as radiator, on the FR4 substrate of 150 × 80 × 0.8 mm with loss tangent (tan δ) of 0.02 and relative permittivity (εr) of 4.4. The proposed antenna resonates at 2.4, 3.5, and 5.5 GHz, and it covers the bandwidth of 2%, 6.28%, and 2.53%, respectively. The measured results provide an omnidirectional radiation pattern with 58%–78% of efficiency in all operating bands. The eight-port multiband MIMO design provides a high isolation of 17.5 dB, envelope correlation coefficient < 0.04, diversity gain of 9.98 dB, total active reflection coefficient < −10 dB, and channel capacity loss of <0.25 bits/s/Hz. Also, the hand phantom is designed to analyze the reflection coefficients and efficiency of the proposed antenna.