This work demonstrates the generation of short pulse duration and high-beam-quality laser pulses using transient stimulated Brillouin scattering at a high repetition rate. Thermal effects and optical breakdown are identified as the main factors that restrict energy reflectivity and beam quality under high repetition rates and transient situations. Through experimental analysis, the interaction length and focal point size are determined to be the key parameters in reducing the thermal effect by reducing the absorption of the laser pulse by the medium. The obtained results show that pulses with a duration of 175 ps and beam quality M2 of around 1.2 can be achieved with a maximum energy reflectivity of over 40% under an interaction length of 50 mm. Furthermore, at an interaction length of 90 mm, a pulse output with a minimum duration of 115 ps (0.5τQ) is achieved.

Beam alignment depends on CCD real-time image analysis and processing. In order to improve the quality of the alignment, multiple filters are used in far-field and near-field image processings. These multiple filters are constituted of an average filter and a median filter in different connection sequences, so that they can deal with different kinds of noise. To reduce the effect of the unknown nonlinear relationship between motor running steps and deviation pixels, a feasible methodology is offered to improve this phenomenon and a fuzzy algorithm is applied to the motor feedback control process. Because of the fuzzy control it is not necessary to establish an accurate mathematical model, so the impact of the nonlinear relationship will be reduced.

Considering the thermodynamical fluid mechanics in the gain medium and laser kinetic processes, a three-dimensional theoretical model of an exciplex-pumped Cs vapor laser with longitudinal and transverse gas flow is established. The slope efficiency of laser calculated by the model shows good agreement with the experimental data. The comprehensive three-dimensional distribution of temperature and particle density of Cs is depicted. The influence of pump intensity, wall temperature, and fluid velocity on the laser output performance is also simulated and analyzed in detail, suggesting that a higher wall temperature can guarantee a higher output laser power while causing a more significant heat accumulation in the cell. Compared with longitudinal gas flow, the transverse flow can improve the output laser power by effectively removing the generated heat accumulation and alleviating the temperature gradient in the cell.

The velocity interferometer system for any reflector (VISAR) coupled with a streaked optical pyrometer (SOP) system is used as a diagnostic tool in inertial confinement fusion (ICF) experiments involving equations of state and shock timing. To validate the process of adiabatically compressing the fuel shell through precise tuning of shocks in experimental campaigns for the double-cone ignition (DCI) scheme of ICF, a compact line-imaging VISAR with an SOP system is designed and implemented at the Shenguang-II upgrade laser facility. The temporal and spatial resolutions of the system are better than 30 ps and 7 μm, respectively. An illumination lens is used to adjust the lighting spot size matching with the target size. A polarization beam splitter and λ/4 waveplate are used to increase the transmission efficiency of our system. The VISAR and SOP work at 660 and 450 nm, respectively, to differentiate the signals from the scattered lights of the drive lasers. The VISAR can measure the shock velocity. At the same time, the SOP system can give the shock timing and relative strength. This system has been used in different DCI campaigns, where the generation and propagation processes of multi-shock are carefully diagnosed.

A method to evaluate damage in optical elements with the near field of an amplified spontaneous emission (ASE) beam has been developed. Local peak intensities are generally distributed randomly in the near field of a laser beam. The partial coherence of the ASE source results in a very smooth beam profile. The coherence time of ASE is much less than the pulse width. Small-scale intensity modulations can be smoothed out rapidly within the time of a pulse width. In the experiments, ASE is generated from a multifunctional high-performance Nd:glass system, with a pulse duration of 3 ns, a spectral width (full width at half maximum, FWHM) of 1 nm and an adjustable energy range from 1 to 10 J. The damage thresholds of samples induced by ASE are two to three times higher than those induced by a laser with the same size of test spot. Furthermore, the ASE beam has great potential for the detection of defects over a large area and the conditioning of optical elements.

Here we report on a simple-to-implement and cost-effective approach for laser pulse contrast enhancement, based on the ${\chi}^{(3)}$ nonlinear self-focusing effect. An intentionally induced and gently controlled self-focusing in a thin glass transforms the time-dependent intensity into variation in beam divergence. Followed by a spatial discriminating filter, only the strongly focused fraction traverses the setup, at the expense of efficiency. A numerical model, accounting for the pulse and material parameters via a Gaussian ABCD matrix, provides an estimate for the instantaneous beam waist and transmission efficiency, which enables us to evaluate the resulting contrast enhancement. The estimated contrast enhancement spans between 0.5 and 2.5 orders of magnitude, in conjunction with approximately 25%–90% estimated efficiency, depending on the pulse parameters. In a preliminary experiment we demonstrated the effect with 10s-μJ sub GW regime with approximately 40$\%$ efficiency and a contrast improvement of more than or equal to 20 dB.

The development of high-intensity ultrafast laser facilities provides the possibility to create novel physical phenomena and matter states. The timing fluctuation of the laser pulses is crucial for pump–probe experiments, which is one of the vital means to observe the ultrafast dynamics driven by intense laser pulses. In this paper, we demonstrate the timing fluctuation characterization and control of the front end of a 100-PW laser that is composed of a high-contrast optical parametric amplifier (seed) and a 200-TW optical parametric chirped pulse amplifier (preamplifier). By combining the timing jitter measurement with a feedback system, the laser seed and preamplifier are synchronized to the reference with timing fluctuations of 1.82 and 4.48 fs, respectively. The timing system will be a key prerequisite for the stable operation of 100-PW laser facilities and provide the basis for potential pump–probe experiments performed on the laser.

The measurement of X-ray continuous emission from laser-driven plasma was achieved through multiple monochromatic imaging utilizing a multilayer mirror array. This methodology was exemplified by the development of an eight-channel X-ray imaging system, capable of operating in the energy range of several keV with a spatial resolution of approximately 3 μm. By integrating this system with a streak camera, the temperature and trajectory of imploding capsules were successfully measured at the kJ-class Shenguang III prototype laser facility. This approach provides a synchronous diagnostic method for the spatial, temporal and spectral analysis of laser-driven plasma, characterized by its high efficiency and resolution.

The development of high-brightness X-ray free electron lasers (XFELs), such as hard X-ray self-seeding free electron lasers and XFEL oscillators (XFELOs), brings a severe challenge to the crystal monochromator due to a strong non-uniform thermal load. The distortion caused by spatial temperature gradients can severely affect the optical performance of crystals. Therefore, this paper presents a model to estimate the performance of non-uniform thermally distorted crystals. The model not only takes into account thermal strain, slope error and incident angle deviation, but also considers temperature-dependent factors such as the Debye–Waller factor and electric susceptibility. Our investigation indicates that the Debye–Waller factor reduces the height and bandwidth of rocking curves, and the impact of the electric susceptibility is tiny. The proposed model can describe the distortion of the reflectivity and transmissivity curves of non-uniform thermally loaded crystals and can be applied in the design of crystal monochromators, crystal splitters, crystal compressors and XFELOs.

Inertial confinement fusion targets are complex systems designed to allow fine control of temperature and pressure for making precise spherical ice layers of hydrogen isotopes at cryogenic temperatures. We discuss the various technical considerations for a maximum leak rate based on heat load considerations. This maximum flow rate turns out to be $5\times 10^{-6}$ standard cc per second, which can be caused by an orifice less than half a micron in diameter. This makes the identification of the location and resolution of the leak a significant challenge. To illustrate this, we showcase one example of a peculiar failure mode that appeared suddenly but persisted whereby target production yield was severely lowered. Identification of the leak source and the root cause requires very careful analysis of multiple thermomechanical aspects to ensure that the end solution is indeed the right remedy and is robust.